1. SCOPE
…………..
2. REFERENCES
3. MATERIALS
1. Scope
This specification covers coatings and coverages for insulation.
2. References
Reference is made in this specification to the following documents. The latest issues, amendments, and
supplements to these documents shall apply unless otherwise indicated.
SABIC Engineering Standards (SES)
N01-F10 Corrosion protection of insulated equipment
American Society for Testing of Materials (ASTM)
ASTM B209 specification for Aluminum and the Aluminum-Alloy sheet and plate
ASTM E84 Surface burning characteristics of building materials.
3. Materials
CODE 709 (Fibrated asphalt cutback)
| Material Designation | Fibrated asphalt cutback |
| Recommended Temperature
Range |
-51 to +163 C (-60 to +325 F) unless indicated otherwise |
| Purpose | A weather- and chemical-resistant vapor-barrier mastic finish for thermal insulation |
| Material Description | Mastic consisting of an asphalt-solvent cutback vehicle, fibers, and fillers of spraying or hard application consistency as specified on purchase order |
| Maximum Leachable Chlorides, see
SES N01-F10 |
Below 250 ppm |
| Moisture Resistance or Water Vapor Permeability |
Very low water vapor permeability |
| Flame-Spread/Smoke-Density
Rating, See ASTM E 84 |
Greater than 25/50. Do not use indoors without sprinkler protection or a fireproof finish. |
| Note | Does not resist solvents and oils. Also used as a joint sealer and bedding compound. Contains volatile solvent and should not be allowed to contact hot surfaces during application. See SES N01-F10 for metal substrate protection required. |
CODE 710 (Glass cloth – open weave)
| Material Designation | Glass cloth – open weave |
| Recommended Temperature | +204 C (+400 F) |
| Range | |
| Purpose | Reinforcement in mastic for thermal insulation |
| Material Description | Open-weave glass cloth produced from glass fiber yarns and compatible with accepted waterproofing and coating compounds. Leno weave to provide fixed thread spacing. Waterproof colorless weave set treatment to minimize distortion of thread spacing. |
| Maximum Leachable Chlorides, see | Below 100 ppm |
| SES N01-F10 | |
| Dimensions | See manufacturer’s literature |
| Flame-Spread/Smoke-Density | 25/50 or less |
| Rating, See ASTM E 84 | |
| Specifications, Qualifications, | Thread count 10 x 10/in2 min, 12 x 13/in2 max. Weight 10 lb/100 yd2 min. Tensile strength by strip method 50 lb/in min in warp direction, and 30 lb/in min in fill direction. Samples to be conditioned and tested at 65% relative humidity. See SN100P for metal substrate protection required. |
| Limitations | |
| Approved Materials and Vendors | Glass Cloth, Style 1659/Geon J. P. Stevens and Co., Inc. |
| Glass Cloth, PGM 207 10 x 10
Perma Glas-Mesh Corp. |
|
| Woven Glass Scrim Fabric, Resin Treated Style 1659
Burlington Industries, Inc. |
|
| Luben Scrim Fabric Style No. 59(a) Alpha Associates, Inc. |
|
| Fiber Glass Serium Style No. 1659
Clark Schwebel Fiber Glass Corp. |
|
| No. 10 Chil-Glas Childers Products Co. |
CODE 714 (Poultry netting)
| Material Designation | Poultry netting |
| Purpose | Reinforcement in finishes for thermal insulation |
| Material Description | Iron or steel wire mesh, galvanized 1 in size |
| Dimensions | See manufacturer’s literature |
| Specifications, Qualifications, Limitations | Iron or steel wire, 20 gage, woven and galvanized. Mesh size 1 in nominal hexagonal openings. |
| Approved Materials and Vendors | Poultry Netting
Most mill supply houses, insulation distributors, and applicators |
DE 714.1 (Poultry netting, coated)
| Material Designation | Poultry netting, coated |
| Purpose | Reinforcement in finishes for thermal insulation |
| Material Description | Galvanized iron or steel wire woven and vinyl coated after weaving, 1 in size |
| Maximum Leachable Chlorides, see
SES N01-F10 |
Below 40,000 ppm |
| Dimensions | See manufacturer’s literature |
| Note | Preferred for use with emulsion coatings such as Code 734 and in corrosive atmospheres. Galvanized iron and steel wire woven and vinyl-coated poultry netting. Mesh size 1 in nominal hexagonal openings. See SES
N01-F10 for metal substrate protection required. |
| Approved Materials and Vendors | Vinyl-Coated Poultry Wire
Most mill supply houses, insulation distributors, and applicators |
CODE 716 (Smooth aluminum jacket, 0.4 mm (16 mil)
| Material Designation | Smooth aluminum jacket, 16 mil |
| Purpose | A finish for thermal insulation where weather resistance, cleanliness, appearance, oil or solvent spills, or fumes are factors |
| Material Description | Smooth aluminum in roll form with a protective backing on inner surface |
| Moisture Resistance or Water
Vapor Permeability |
Impermeable |
| Resistance to Handling Breakage | Good |
| Dimensions | Width: 914 mm or 1220 mm (36 or 48 in) Length: Rolls of 30 m(100 ft) minimum
Thickness of aluminum:0.4 mm (0.016 in) nominal |
| Note | Attacked by most acids, chlorides, and some hydroxides. Check exposure before specifying. The protective backing shall be a minimum of 65 mµ (2.5 mil) total thickness coextruded polyethylene and DuPont Surlyn continuously heat-sealed to the metal. The Surlyn shall be a minimum of
25 mµ (1 mil). The protective backing shall qualify per SN219P. Aluminum sheeting conforms to ASTM B 209. |
| Approved Materials and Vendors | Aluminum Jacket with 2.5 Mil Poly/Surlyn
Childers Products Co. |
| Sure-Fit Roll Jacketing with 2.5 Mil Poly/Surlyn
Pabco Division of Fibreboard Corp. |
|
| 16 Mil Aluminum Jacket with 2.5 Mil Poly/Surlyn
RPR Products, Inc. |
CODE 716.5 (Smooth aluminum jacket, (16 mil) acrylic-coated)
| Material Designation | Smooth aluminum jacket, (16 mil) acrylic-coated |
| Purpose | A finish for thermal insulation where weather or chemical resistance, cleanliness, appearance, oil or solvent spills, or fumes are factors |
| Material Description | Smooth aluminum in roll form with a white acrylic coating on exterior and a protective backing on inner surface |
| Moisture Resistance or Water
Vapor Permeability |
Impermeable |
| Resistance to Handling Breakage | Good |
| Dimensions | Width: Standard 36 in (48 in at additional cost) Length: Roll of 100 ft/min
Thickness of aluminum: 0.016 in nominal |
| Note | Exterior surface to have a white acrylic coating nominal 0.8 mil dry-film thickness. Some acids will attack coating. Check exposure before specifying. The protective backing shall be a minimum of 2.5 mil total thickness coextruded polyethylene and DuPont Surlyn continuously heat-sealed to the metal. The Surlyn shall be a minimum of 1 mil. The
protective backing must qualify per SN219P. Aluminum sheeting conforms to ASTM B 209. |
| Approved Materials and Vendors | Aluminum Jacket, Acrylic Finish with 2.5 Mil Poly/Surlyn
Childers Products Co. |
| Acrylic Coated Aluminum Jacket with 2.5 Mil Poly/Surlyn
RPR Products, Inc. |
|
| Sure-Fit Roll Jacketing, Acrylic Coated with 2.5 Mil Poly/Surlyn
Pabco Div. of Fibreboard Corp. |
CODE 716.6 (Deep-corrugated aluminum jacket, 16 mil)
| Material Designation | Deep-corrugated aluminum jacket, 16 mil |
| Purpose | A finish for thermal insulation on vertical vessels. Preferred finish where rigidity, weather resistance, cleanliness, appearance, oil or solvent spills, or fumes are factors. |
| Material Description | Aluminum sheets with 11/4 in corrugations and a protective backing on the interior surface. A more rigid material than Code 716. Finish: smooth or cross-crimped as specified on order. |
| Moisture Resistance or Water
Vapor Permeability |
Impermeable |
| Resistance to Handling Breakage | Good |
| Dimensions | Width: 33 in (36 in available at added cost) Length: Up to 12 ft
Thickness: 0.016 in nominal |
| Note | Attacked by most acids, chlorides, and some hydroxides. Check exposure before specifying. The protective backing shall be 40 lb/3000 ft2 kraft paper and 3 mil polyethylene extrusion laminate heat-sealed to the aluminum sheet over the entire interface area or a minimum of 2.5 mil total thickness coextruded polyethylene and DuPont Surlyn continuously heat-sealed to the metal. The Surlyn shall be a minimum of 1 mil. The poly/kraft protective backing shall be identified on the product to indicate 3 mil polyethylene. The protective backing must qualify per SN219P. Aluminum sheeting conforms to ASTM B 209. |
| Approved Materials and Vendors | Deep-Corrugated Jacketing with 3 Mil Poly/Kraft or 2.5 Mil Poly/Surlyn (a)
Childers Products Co. |
| Sure-Fit Deep-Corrugated Sheets – Aluminum with 3 Mil
Poly/Kraft or 2.5 Mil Poly/Surlyn Pabco Div. of Fibreboard Corp. |
|
| Deep-Corrugated Aluminum with 3 Mil Poly/Kraft or 2.5 Mil Poly/Surlyn
RPR Products, Inc. |
CODE 716.7 (Deep-corrugated aluminum jacket, 16 mil acrylic-coated)
| Material Designation | Deep-corrugated aluminum jacket, 16 mil acrylic-coated |
| Purpose | A finish for thermal insulation on vertical vessels. Preferred finish where rigidity, weather or chemical resistance, cleanliness, appearance, oil or solvent spills, or fumes are factors. |
| Material Description | Aluminum sheets with 11/4 in corrugations and a white acrylic coating on the exterior and a protective backing on the interior surface. A more rigid material than Code 716.5. |
| Moisture Resistance or Water
Vapor Permeability |
Impermeable |
| Resistance to Handling Breakage | Good |
| Dimensions | Width: 33 in (36 in available at added cost) Length: Up to 12 ft
Thickness: 0.016 in nominal |
| Note | Exterior surface to have a white acrylic coating nominal 0.8 mil dry-film thickness. Some acids will attack coating. Check exposure before specifying. The protective backing shall be 40 lb/3000 ft2 kraft paper and
3 mil polyethylene extrusion laminate heat-sealed to the aluminum sheet over the entire interface area or a minimum of 2.5 mil total thickness coextruded polyethylene and DuPont Surlyn continuously heat-sealed to the metal. The Surlyn shall be a minimum of 1 mil. The poly/kraft protective backing shall be identified on the product to indicate 3 mil polyethylene. The protective backing must qualify per SN219P. Aluminum sheeting conforms to ASTM B 209. |
| Approved Materials and Vendors | Deep-Corrugated Aluminum Jacket, Acrylic Finish with 3 Mil Poly/Kraft or
2.5 Mil Poly/Surlyn (a) Childers Products Co. |
| Sure-Fit Deep-Corrugated Sheets – Aluminum Acrylic-Coated with 3 Mil
Poly/Kraft or 2.5 Mil Poly/Surlyn Pabco Div. of Fibreboard Corp. |
|
| Deep-Corrugated Aluminum with 3 Mil Poly/Kraft or 2.5 Mil Poly/Surlyn
Acrylic-Coated RPR Products, Inc. |
Note:
(a) State complete specification and required length on order.
CODE 716.8 (Smooth aluminum jacket, 16 mil Tedlar coated)
| Material Designation | Smooth aluminum jacket, 16 mil Tedlar coated |
| Purpose | A finish for thermal insulation where specific chemical resistance, cleanliness, appearance, oil or solvent spills, or fumes are factors |
| Material Description | Smooth aluminum in roll form with a white Tedlar PVF film laminated to the exterior and a protective backing on inner surface(a) |
| Moisture Resistance or Water
Vapor Permeability |
Impermeable |
| Resistance to Handling Breakage | Good |
| Dimensions | Width: Standard 351/2 in
Length: Roll of 100 ft minimum Thickness of aluminum: 0.016 in nominal Thickness of Tedlar PVF film: 1.5 mil |
| Note | White Tedlar PVF film 1.5 mil thick laminated to exterior surface resistant to most acids, bases, and solvents. Check exposure before specifying. The protective backing shall be a minimum of 2.5 mil total thickness coextruded polyethylene and DuPont Surlyn continuously heat-sealed to the metal. The Surlyn shall be a minimum of 1 mil. The protective backing must qualify per SN219P. Aluminum sheeting conforms to ASTM B 209. |
| Approved Materials and Vendors | Aluminum Jacket, Ultrolon Finish with 2.5 Mil Poly/Surlyn
Childers Products Co. |
| Aluminum Jacket, Tedlar, Coated with 2.5 Mil Poly/Surlyn
RPR Products, Inc. |
Note:
(a) Additional colors are available on special large orders.
CODE 717.1 (45 and 90 ell covers, two-piece aluminum die-formed)
| Material Designation | 45 and 90 ell covers, two-piece aluminum die-formed |
| Purpose | A finish for thermal insulation on pipe fittings |
| Material Description | Sheet aluminum cold-formed into two-piece covers by die-forming. Ends have 2 in tangents for lap joints with pipe insulation covering. Fits only one combination of pipe size and insulation thickness. Insulation must be mitered per vendor’s pattern to prevent interferences. Inside surface coated with transparent epoxy finish. |
| Moisture Resistance or Water
Vapor Permeability |
Impermeable |
| Resistance to Handling Breakage | Good |
| Dimensions | Available for pipe sizes through 12 in and 11/2 diameter or smaller bends
Thickness of formed covers: 0.016 in min |
| Note | Attacked by most acids, chlorides, and some hydroxides. Check exposure before specifying. The protective backing must qualify per SN219P. Humped or ‘universal’ type covers are not acceptable. |
| Approved Materials and Vendors | Ell-Jac, CE5-6 Moisture Barrier(a)
Childers Products Co. |
| Sure-Fit Elbow Covers
Pabco Div. of Fibreboard Corp. |
|
| 2-Piece Aluminum Elbow Covers
RPR Products, Inc. |
Note:
(a) Four-piece aluminum die-formed ell covers are available in sizes to 18 in by 2 in.
CODE 717.8 (Aluminum covers for vessel heads)
| Material Designation | Aluminum covers for vessel heads |
| Purpose | Weatherproof and protect insulated heads |
| Material Description | Sheet aluminum cut into gore and beaded, then fabricated into head cover |
| Moisture Resistance or Water
Vapor Permeability |
Impermeable |
| Resistance to Handling Breakage | Good |
| Dimensions | Thickness: 0.020 in nominal
Size Range: 1 ft through 20 ft diameter (6 in increments) |
| Note | Attacked by most acids, chlorides, and some hydroxides. Check exposure before specifying. The protective backing shall be a minimum of 2.5 mil total thickness coextruded polyethylene and DuPont Surlyn continuously
heat-sealed to the metal. The Surlyn shall be a minimum of 1 mil. The protective backing must qualify per SN219P. Vendor will require specific dimensional information on the vessel. Aluminum sheeting conforms to ASTM B 209. |
| Approved Materials and Vendors | Aluminum Gore Head-Jacs with 2.5 Mil Poly/Surlyn
Childers Products Co. |
| Aluminum Gore Heat Jacket with 2.5 Mil Poly/Surlyn
Distribution International |
|
| Aluminum Gore Head Jacket with 2.5 Mil Poly/Surlyn
RPR Products, Inc. |
CODE 717.9 (End cap with pipe collar, two-piece aluminum)
| Material Designation | End cap with pipe collar, two-piece aluminum |
| Purpose | A finish for thermal insulation on open-end pipe insulation |
| Material Description | Sheet aluminum fabricated into two-piece covers by rolling and Pittsburgh lock seal, with a 1 in min wide flange fitted to the outside diameter of the pipe. Fits only one combination of pipe size and insulation thickness. |
| Moisture Resistance or Water
Vapor Permeability |
Impermeable |
| Resistance to Handling Breakage | Good |
| Dimensions | Thickness: 0.016 in nominal
Size Range: 4 in by 11/2 in through 24 in by 4 in |
| Note | Attacked by most acids, chlorides, and some hydroxides. Check exposure before specifying. The protective backing shall be a minimum of 2.5 mil total thickness coextruded polyethylene and DuPont Surlyn continuously
heat-sealed to the metal. The Surlyn shall be a minimum of 1 mil. The protective backing must qualify per SN219P. |
| Approved Materials and Vendors | Double Flanged Collar-Jac with 2.5 Mil Poly/Surlyn
Childers Products Co. |
| Double Flanged Collar with 2.5 Mil Poly/Surlyn
RPR Products, Inc. |
CODE 720(a) (Glass cloth with adhesive (rewettable))
| Material Designation | Glass cloth with adhesive (rewettable) | |
| Recommended Temperature | +343 C max (+650 F max) | |
| Range | ||
| Purpose | Asbestos-free thermal insulation covering | |
| Material Description | A woven glass lagging cloth impregnated with a complete coverage of rewettable, inorganic adhesive | |
| Maximum Leachable Chlorides, see | Below 100 ppm | |
| SES N01-F10 | ||
| Moisture Resistance or Water | Water soluble adhesive | |
| Vapor Permeability | ||
| Dimensions | Width: 40 or 60 in
Length: 50 or 100 yd rolls |
|
| Flame-Spread/Smoke-Density | 25/50 or less | |
| Rating, See ASTM E 84 | ||
| Note | Must be protected from moisture prior to and after installation.
Self-contained adhesive is instantly activated by dipping in water. Drapes well on compound curved surfaces and around sharp corners. Compatible with most waterproofing mastics and coatings. Not recommended for use on removable-reusable covers that are handled frequently. Lagging adhesive, Code 802.1, or fibrous adhesive, Code 803, is not needed. If used, these materials will attack the glass cloth. See SES N01-F10 for metal substrate protection required. |
|
| Approved Materials and Vendors | Alpha-Maritex Style No. 84215/9485-RW(b)
Alpha Associates, Inc. |
|
| S/2205 RWL Covergard(c)
Southern Mfg., Inc. |
||
| Textoglass, Style No. 84217/9995(b), J. P. Stevens Co. | ||
| Textoglass, Style No. 2014/9995(d), J. P. Stevens Co. | ||
| Claretex Lagging Fabric No. 84205, Diplag Treated(d)
The Claremont Co., Inc. |
||
| 300-RWL
Newtex Industries |
Notes:
(a) Does not contain respirable fibers.
(b) 15 oz/yd2
(c) Specify 15 oz/yd2 or 26 oz/yd2 (d) 22 oz/yd2
CODE 723.1 (‘ASJ’ Kraft aluminum laminate – white)
| Material Designation | ‘ASJ’ Kraft aluminum laminate – white | |
| Recommended Temperature | +2 to +82 C (+35 to +180 F max) | |
| Range | ||
| Purpose | An indoor finish for thermal insulation | |
| Material Description | Glass mesh, approximately 4 in x 6 in, 0.7 mil aluminum foil and white kraft paper bonded together by a fire-retardant adhesive. Finish creped to minimize wrinkling. | |
| Moisture Resistance or Water | Not to exceed 0.02 perms | |
| Vapor Permeability | ||
| Dimensions | Width: 391/4 in
Other widths on request Length: 100 yd rolls |
|
| Flame-Spread/Smoke-Density | 25/50 or less | |
| Rating, See ASTM E 84 | ||
| Note | No soluble salts are to be used as the fire-retardant agent. May be used outdoors if protected with aluminum jacket, Code 716. Laminating adhesive to be insoluble in water and have a softening point of not less than 170 F. | |
| Approved Materials and Vendors | Alpha-Temp 10651 ASJ Alpha Associates, Inc. | |
| FB 200 ASJ Compac Corp. |
CODE 725 (PVA insulation coating for indoors)
| Material Designation | PVA insulation coating for indoors | |
| Recommended Temperature | -46 to 82 C (-50 to +180 F max) | |
| Range | ||
| Purpose | Indoor fire-resistant protective coating for thermal insulation and an adhesive for canvas jackets | |
| Material Description | Brush or spray consistency, white polyvinyl acetate emulsion, suitable for reinforcement with glass cloth | |
| Maximum Leachable Chlorides, see | Below 43,000 ppm | |
| SES N01-F10 | ||
| Moisture Resistance or Water | Permeable | |
| Vapor Permeability | ||
| Flame-Spread/Smoke-Density | 25/50 or less (dry) | |
| Rating, See ASTM E 84 | ||
| Note | Recommended for indoor use only. Should not be applied at temperatures below +40 F. Coverage approx 50 ft2/gal. Store above +32 F.
Drying time: Touch 1 hour through 4 hours. See SES N01-F10 for metal substrate protection required. |
|
| Approved Materials and Vendors | Foster Sealfas 30-36(a)
H.B. Fuller Co., Foster Products Div. |
|
| Chil-Seal CP-50A Childers Products Co. | ||
| Eco-Perm Coating 11-02
Mon-Eco Industries, Inc. |
Note:
(a) White, other colors available.
CODE 727.1(a) (Flexible braided glass fiber tubing)
| Material Designation | Flexible braided glass fiber tubing | |
| Recommended Temperature | +10 to 260 C (+50 to +500 F) | |
| Range | ||
| Purpose | Thermal insulation for bent pipe or tubing where use of rigid material is impractical | |
| Material Description | Lightweight, flexible braided tubing manufactured from continuous filament glass fiber and specially heat-treated | |
| Maximum Leachable Chlorides, see | Below 100 ppm | |
| SES N01-F10 | ||
| Resistance to Handling Breakage | Good | |
| Dimensions | Fits 1/8 in to 3 in OD tubing | |
| Flame-Spread/Smoke-Density | 25/50 or less | |
| Rating, See ASTM E 84 | ||
| Note | Attacked by hydrofluoric and phosphoric acids and concentrated hot alkalies. Unaffected by other corrosive agents. Resists organic solvents. See SES N01-F10 for metal substrate protection required. | |
| Approved Materials and Vendors | Thermojacket R Unsaturated
Bentley-Harris Manufacturing Co. |
|
| Thermoglass Sleeving, Style No. 10–700, Series 9731 Finish
Amatex Corp. |
||
| Alpha Maritex Braided Sleeving, 9400 Series
Alpha Associates, Inc. |
||
| Woven Tubing
Auburn Manufacturing Inc. |
Note:
(a) Does not contain respirable fibers.
CODE 728.1 (Tedlar, glass, Hypalon laminate)
CODE 730 (Hypalon coating)
| Material Designation | Hypalon coating | |
| Recommended Temperature | -29 to +121 C max (-20 to +250 F max) | |
| Range | ||
| Purpose | Vapor-barrier finish for thermal insulation in either low temperature service or severely corrosive environment or both | |
| Material Description | A pigmented, fire-resistant elastomeric coating. Two-coat system. First coat strikes the surface in webs that bridge porous substrates and produce a smooth water-repellent coating. Top coat seals to produce a vaportight coating. Air spray application only. | |
| Maximum Leachable Chlorides, see | Below 100 ppm | |
| SES N01-F10 | ||
| Moisture Resistance or Water | Very low water vapor permeability | |
| Vapor Permeability | ||
| Flame-Spread/Smoke-Density | 25/50 or less | |
| Rating, See ASTM E 84 | ||
| Note | Excellent resistance to chemicals and some solvents. A primer is recommended on dusty and resilient substrates. Spray only. Compounded with Hypalon synthetic rubber. Drying and recoat time: 4 to 8 hours. See SES N01-F10 for metal substrate protection required. | |
| Approved Materials and Vendors | Flexgard Finish System
Guardsman Chemical Coating Corp. |
|
| Gacoflex H2500
Gates Engineering Co. |
CODE 731 (Hypalon mastic)
| Material Designation | Hypalon mastic | |
| Recommended Temperature Range | -29 to +121 C max (-20 to +250 F max) | |
| Purpose | Chemical-resistant, vapor-barrier finish for thermal insulation, especially irregular surfaces | |
| Material Description | Flexible, pigmented, fire-resistant elastomer coating of mastic consistency | |
| Maximum Leachable Chlorides, see | Below 100 ppm | |
| SES N01-F10 | ||
| Moisture Resistance or Water | Very low water vapor permeability | |
| Vapor Permeability | ||
| Flame-Spread/Smoke-Density | 25/50 or less | |
| Rating, See ASTM E 84 | ||
| Note | Contains flammable solvents during application and curing period. May require a primer for adhesion to dusty substrates. Minimum acceptable cured finish: 30 mil applied in at least two coats. Compounded with Hypalon synthetic rubber.
Drying time: Touch 3 hours Flexibility: 30 mil (6 gal/100 ft2) cured coating can be bent over 1/8 in diameter mandrel through 180 degree arc without cracking per Federal Test Method Standard No. 141. Method 6221. Spray only. Check manufacturer for required spray equipment and technique. See SES N01-F10 for metal substrate protection required. |
|
| Approved Materials and Vendors | Foster Monolar, Trowel,
60-90 (white) 60-91 (gray) Spray, 60-95 (white) 60-96 (gray) H. B. Fuller Co., Foster Products Div. |
|
CODE 734 (Insulation mastic)
| Material Designation | Insulation mastic | |
| Recommended Temperature | -18 to +82 C max (0 to +180 F max) | |
| Range | ||
| Purpose | Protective acrylic mastic coating for thermal insulation | |
| Material Description | This code number is for white, other colors are available. Nonasphalt pigmented emulsion mastic for rubber glove, palm, brush, or spray application | |
| Maximum Leachable Chlorides, see | Below 150 ppm | |
| SES N01-F10 | ||
| Flame-Spread/Smoke-Density | 25/50 or less | |
| Rating, See ASTM E 84 | ||
| Note | Do not apply at temperature below +40 F Store above +32 F
Drying time: Touch 3 hours Thorough drying time: 12 to 24 hours Coverage: 10 to 15 ft2 /gal for the system of tack coat and finish coat using reinforcing. Do not use as a vapor barrier. Limited service life for outdoor environment. See SES N01-F10 for metal substrate protection required. |
|
| Approved Materials and Vendors | Foster Weatherite Mastic
36-10 (Trowel) 46-10 (Spray) H. B. Fuller Co., Foster Products Div. |
|
| Vi-Cryl CP-10 Trowel, CP-11 Brush
Childers Products Co. |
||
| Vimasco WC-5 Mastic
Vimasco Corp. |
||
| Eco-Mastic 55-50
Mon-Eco Industries, Inc. |
||
| Jaxsan 600
Plastic Coatings Corp. |
| L&L Pro-Tec 638
L&L Coatings Corp. |
CODE 741 (Vapor-barrier membrane)
| Material Designation | Vapor-barrier membrane |
| Recommended Temperature | -32 to +66 C max (-25 to +150 F max) |
| Range | |
| Purpose | Vapor barrier for thermal insulation |
| Material Description | A flexible membrane consisting of a plastic film coated on one side with adhesive-consistency mastic covered with a release paper |
| Maximum Leachable Chlorides, see | Below 150 ppm |
| SES N01-F10 | |
| Moisture Resistance or Water | 0.05 perms max |
| Vapor Permeability | |
| Dimensions | Width: 36 in
Length: 50 or 60 ft rolls with release paper |
| Flame-Spread/Smoke-Density Rating, See ASTM E 84 | Greater than 25/50
Do not use indoors without sprinkler protection or a fireproof finish |
| Note | Protect from heat and direct sunlight prior to use to reduce handling difficulties due to softening. Ambient surface and material temperatures should not be below +40 F at time of application. Overlaps on itself to form a self-sealing seam. Protect from sunlight outdoors and cover as soon as possible after application. Membrane to be 5 to 10 mil plastic film with 40 to
60 mil layer of adhesive-consistency mastic. See SES N01-F10 for metal substrate protection required. |
| Approved Materials and Vendors | Serci Wrap P500
Ultra Industries |
| Pittwrap SS II
Pittsburgh Corning Corp. |
CODE 743(a) (Synthetic organic fiber cloth, open weave)
| Material Designation | Synthetic organic fiber cloth, open weave |
| Recommended Temperature | +121 C max (+250 F max) |
| Range | |
| Purpose | High-elongation reinforcement for mastic finishes over thermal insulation |
| Material Description | An open mesh cloth consisting of mod-acrylic or nylon and polyester fiber and treated with a weave set |
| Maximum Leachable Chlorides, see | Below 150 ppm |
| SES N01-F10 | |
| Flame-Spread/Smoke-Density | 25/50 or less |
| Rating, See ASTM E 84 | |
| Note | High elongation accommodates thermal and mechanical movement without rupture. Elongation 30%: min 21/2 to 3 oz/yd2: meshes per in from 5 x 5 to 8 x 8 mesh openings per in. Compatible with asphalt cutback and emulsion mastic finishes. May be softened by some solvents such as acetone and ketones. See SES N01-F10 for metal substrate protection required. |
| Approved Materials and Vendors | Elastafab No. 894
Vimasco Corp. |
| PC Fabric 79
Pittsburgh Corning Corp. Quality Cloth Distribution International |
Note:
(a) Does not contain respirable fibers.
CODE 745(a) (High-temperature glass cloth)
| Material Designation | High-temperature glass cloth | |||
| Recommended Temperature | +343 C max (+650 F max) | |||
| Range | ||||
| Purpose | Covering for insulation materials used for removable pads, flange covers, and insulation blankets | |||
| Material Description | Plain weave fabric, woven with 100% fiberglass high bulk yarns | |||
| Maximum Leachable Chlorides, see | Below 100 ppm | |||
| SES N01-F10 | ||||
| Density | 17 oz/yd2 | |||
| kg/m3 (lb/ft3) | ||||
| Resistance to Handling Breakage | Good | |||
| Dimensions | Standard Widths (in)
Alpha 38, 50, 60, 72 Amatex 60 Burlington 38, 50, 60 Stevens 38, 50, 60, 72 |
|||
| Flame-Spread/Smoke-Density Rating, See ASTM E 84 | 25/50 or less | |||
| Approved Materials and Vendors | Alpha-Maritex, Style 2025/9383, Alpha Associates, Inc.
Thermoglass, Style GI9P33, Amatex Corp. |
|||
| Burlglas, Style 1925, Finish I – 603A, Burlington Industries, Inc. | ||||
| Textoglass, Style 1925, Finish 9383, J. P. Stevens and Co., Inc. | ||||
| Claretex 1925, Pad Fabric, The Claremont Co., Inc. | ||||
| Clark Schwebel Glass Fabric, Style 1925/9383
Clark Schwebel Fiber Glass Corp. |
||||
| Style 2025 – 100 Finish
Southern Manufacturing, Inc. |
||||
| AMI-Glass Style GL-2025-9383
Auburn Manufacturing, Inc. |
||||
| Zetex Style 600
Newtex Industries |
| Note | Maximum service temperature is +1000 F; however, the material retains only approximately 50% of room temperature tensile strength at +700 F and approximately 25% at +900 F. Do not use outdoors or in wet areas. Can be machine sewn. See SES N01-F10 for metal substrate protection required. |
Note:
(a) Does not contain respirable fibers.
CODE 746(a) (High-temperature glass cloth, silicone-coated)
| Material Designation | High-temperature glass cloth, silicone-coated | |
| Recommended Temperature | +38 to +260 C max (+100 to +500 F max) | |
| Range | ||
| Purpose | Covering for insulation materials used for removable-reusable pads, flange covers, and insulation blankets – indoors | |
| Material Description | Glass fiber fabric coated with silicone rubber both sides | |
| Maximum Leachable Chlorides, see | Below 100 ppm | |
| SES N01-F10 | ||
| Moisture Resistance or Water | Nonporous | |
| Vapor Permeability | ||
| Density | 15 oz/yd2 | |
| kg/m3 (lb/ft3) | ||
| Resistance to Handling Breakage | Good | |
| Dimensions | 36, 38, 48, 50, and 60 in width | |
| Flame-Spread/Smoke-Density | 25/50 or less | |
| Rating, See ASTM E 84 | ||
| Note | The maximum service temperature of the silicone rubber coating is +500 F. Water, oil, grease, acid, and alkali resistant. Can be machine-sewn. Do not use outdoors or in wet areas indoors. Available in gray color only. See SES N01-F10 for metal substrate protection required. | |
| Approved Materials and Vendors | Alpha-Maritex Style 3201-2-SS Alpha Associates, Inc. | |
| Style 2300 – Silicone-Coated
Southern Manufacturing, Inc. |
||
| Lewco 1600S
Lewco Specialty Products, Inc. |
||
| Silverjac 1700
Style 3155 Silicone/Glass McAllister Mills Textiles Coated, Inc. Thermoglass, Style G17SIL Amatex Corp. |
||
Note:
(a) Does not contain respirable fibers.
CODE 746.1(a) (High-temperature glass cloth, silicone-impregnated)
| Material Designation | High-temperature glass cloth, silicone-impregnated | |
| Recommended Temperature | +38 to +260 C max (+100 to +500 F max) | |
| Range | ||
| Purpose | Covering for insulation materials used for removable-reusable pads, flange covers, and insulation blankets – outdoors | |
| Material Description | Satin weave glass fiber fabric impregnated with silicone rubber both sides | |
| Maximum Leachable Chlorides, see | Below 100 ppm | |
| SES N01-F10 | ||
| Moisture Resistance or Water | Nonporous | |
| Vapor Permeability | ||
| Density | 17 oz/yd2 | |
| kg/m3 (lb/ft3) | ||
| Resistance to Handling Breakage | Good | |
| Dimensions | 36, 38, 48, 50, and 60 in widths | |
| Flame-Spread/Smoke-Density | 25/50 or less | |
| Rating, See ASTM E 84 | ||
| Note | The maximum service temperature of the silicone rubber coating is +500 F. Water, oil, grease, acid, and alkali resistant. Can be machine-sewn. Available in gray color only. See SES N01-F10 for metal substrate protection required. | |
| Approved Materials and Vendors | Alpha-Maritex Fiber Glass/Silicone Style 3259-2-SS Alpha Associates, Inc. | |
| Silverjac 1700
Textiles Coated, Inc. Lewco 1700S Lewco 1750SA Lewco Specialty Products, Inc. |
||
Note:
(a) Does not contain respirable fibers.
CODE 746.2(a) (High-temperature glass cloth, Teflon-coated)
| Material Designation | High-temperature glass cloth, Teflon-coated |
| Recommended Temperature | +38 to +260 C max (+100 to +500 F max) |
| Range | |
| Purpose | Chemical and weather resistant Teflon-coated cloth developed specifically for fabricating removable-reusable soft insulating covers/pads |
| Material Description | Woven glass fabric coated with Teflon fluorocarbon resins |
| Maximum Leachable Chlorides, see | Below 100 ppm |
| SES N01-F10 | |
| Moisture Resistance or Water | Nonporous |
| Vapor Permeability | |
| Density | 14 oz/yd2 |
| kg/m3 (lb/ft3) | |
| Resistance to Handling Breakage | Excellent |
| Dimensions | Roll 5 ft wide x 50 yd long |
| Flame-Spread/Smoke-Density Rating, See ASTM E 84 | 25/50 or less |
| Note | Maximum service temperature of the Teflon coating is +500 F. Water, oil, grease, acid, and alkali resistant. Can be machine-sewn and heat-sealed. Available in gray color only. See SES N01-F10 for metal substrate protection required. |
| Approved Materials and Vendors | Alpha Maritex Style TC-q-14 ‘Teflon’ -Coated Fiberglass
Fabric Alpha Associates, Inc. q-Guard 14G Chemfab Material Technologies Div. EJ1650 Textiles Coated, Inc. |
Note:
(a) Does not contain respirable fibers.
CODE 747(a) (High-temperature synthetic cloth)
| Material Designation | High-temperature synthetic cloth | |
| Recommended Temperature Range | +288 C max (+550 F max) | |
| Purpose | Covering for insulation materials used for removable-reusable insulation indoors | |
| Material Description | Heat-resistant, synthetic textile consisting of a combination of glass, Nomex and Kevlar fibers. Also available as tape, roving, braided sleeving, and twisted and braided rope. | |
| Maximum Leachable Chlorides, see SES N01-F10 | Below 100 ppm | |
| Density kg/m3 (lb/ft3) | 17 and 22 oz/yd2 | |
| Resistance to Handling Breakage | Excellent | |
| Dimensions | 40 and 60 in widths in 50 yd rolls | |
| Flame-Spread/Smoke-Density | 25/50 or less | |
| Rating, See ASTM E 84 | ||
| Note | Has high abrasion resistance and high mechanical strength. Other weights of cloth are available. Can be adhered with lagging adhesive Code 802.1 and fibrous adhesive Code 803 and Code 803.2 (trowel grade), and exposed to +550 F without apparent loss of cloth strength. Available only in
pale yellow color. See SES N01-F10 for metal substrate protection required. |
|
| Approved Materials and Vendors | Nor-Fab 400
Amatex Corp. |
Note:
(a) Does not contain respirable fibers.
CODE 748 (45 and 90 ell covers, one-piece PVC – indoor)
| Material Designation | 45 and 90 ell covers, one-piece PVC – indoor | |
| Recommended Temperature | -18 to +66 C max (0 to +150 F max) | |
| Range | ||
| Purpose | Finish over thermal insulation on pipe fittings. To be used on pipe fittings where fiberglass insulation with factory-applied ASJ (kraft aluminum – white) finish is specified indoors. | |
| Material Description | Sheet polyvinylchloride, preformed into one-piece covers. Fits only one combination of fitting size and insulation thickness. | |
| Maximum Leachable Chlorides, see | Below 40,000 ppm | |
| SES N01-F10 | ||
| Moisture Resistance or Water | 0.05 perms max | |
| Vapor Permeability | ||
| Resistance to Handling Breakage | Good | |
| Dimensions | Thickness: 0.020 in minimum
Max available size 12 x 11/2 in(a) |
|
| Flame-Spread/Smoke-Density | 25/50 or less | |
| Rating, See ASTM E 84 | ||
| Note | Covers can be secured with vinyl tape, nylon tacks, or adhesives. Accessories are available from the fitting cover distributors. PVC will soften above 71 C (160 F). Specify one-piece fitting cover – economical fitting cover to be used indoors in low-mechanical abuse areas. Not recommended outdoors. See SES N01-F10 for metal substrate protection required. | |
| Approved Materials and Vendors | 300 Series PVC, UVR, Light-Gage Fitting Cover
CEEL-Co |
|
| Dura-Jac SX Fitting Cover
Sproule Mfg. Co. |
||
| Speedline 2
Great Lakes Inc. |
||
| LoSmoke
Proto Corp. P.I.C. FG20 P.I.C. Plastics, Inc. Zeston 2000 Manville Mechanical Insulation Div. Schuller International, Inc. |
||
Note:
(a) For availability of larger sizes, contact vendor.
CODE 748.1 (45 and 90 ell covers, one-piece PVC)
| Material Designation | 45 and 90 ell covers, one-piece PVC |
| Recommended Temperature Range | -18 to +66 C max (0 to +150 F max) |
| Purpose | Finish over thermal insulation on pipe fittings. To be used on pipe fittings where fiberglass insulation with factory-applied ASJ (kraft aluminum – white) finish is specified indoors. |
| Material Description | Sheet polyvinylchloride, preformed into one-piece covers. Fits only one combination of fitting size and insulation thickness. |
| Maximum Leachable Chlorides, see SES N01-F10 | Below 40,000 ppm |
| Moisture Resistance or Water Vapor Permeability | 0.05 perms max |
| Resistance to Handling Breakage | Good |
| Dimensions | Thickness: 0.030 in minimum
Max available size 20 in OD |
| Flame-Spread/Smoke-Density Rating, See ASTM E 84 | Less than 25/greater than 50. Do not use indoors without sprinkler protection or a fireproof finish. |
| Note | Covers can be secured with vinyl tape, nylon tacks, or adhesives. Accessories are available from the fitting cover distributors. Specify one-piece fitting cover – economical fitting cover to be used indoors in low-mechanical abuse areas. PVC will soften above 71 C (160 F).
Unaffected by ultraviolet rays. Check chemical exposure before specifying. See SES N01-F10 for metal substrate protection required. |
| Approved Materials and Vendors | Ceel-Tite 300 Series Heavy Duty
CEEL-Co. |
| Dura-Jac SX 0.030 in
Sproule Mfg. Co. |
|
| Industrial Weight PVC Proto Corp. | |
| P.I.C. FG30
P.I.C. Plastics, Inc. Zeston 2000 Heavy Gage Manville Mechanical Insulation Div. Schuller International, Inc. |
CODE 748.2 (two-piece PVC flange cover)
| Material Designation | two-piece PVC flange cover |
| Recommended Temperature Range | -18 to +66 C max (0 to +150 F max) |
| Purpose | Corrosion-resistant permanent or removable-reusable flange cover that is suitable for DuPont spacing of pipe insulation at flanges |
| Material Description | Heavy-gauge sheet polyvinylchloride, preformed into two-piece matching covers. Fits only one combination of flange size (150 through 400 lb) and pipe insulation thickness. |
| Maximum Leachable Chlorides, see SES N01-F10 | Below 40,000 ppm |
| Moisture Resistance or Water Vapor Permeability | 0.05 perms max |
| Resistance to Handling Breakage | Good |
| Dimensions | Thickness: 0.040 in minimum
Max available size: 12 in by 21/2 in Larger sizes available on special order |
| Flame-Spread/Smoke-Density | Less than 25/greater than 50. Do not use indoors without sprinkler protection or a fireproof finish. |
| Rating, See ASTM E 84 | |
| Note | Designed to accept 21/2 in thick insulation. The insulation can be installed loose or can be secured to the inside of the cover with adhesive. Can be used indoors or outdoors in moderate mechanical abuse areas. This cover is compatible with white acrylic or Tedlar-coated aluminum pipe insulation jacketing. Unaffected by ultraviolet rays. PVC will soften above 71 C
(160 F). Check chemical exposure before specifying. See SES N01-F10 for metal substrate protection required. |
| Approved Materials and Vendors | EX-L-FLG Proto Corp.
Dura-Jac SX Flange & Ball Valve Cover Sproule Mfg. Co. |
CODE 748.3 (30 mil PVC jacket)
| Material Designation | 30 mil PVC jacket |
| Recommended Temperature | -18 to +66 C max (0 to +150 F max) |
| Range | |
| Purpose | Finish for thermal insulation where abuse resistance, weather or chemical resistance, cleanliness, appearance, oil or solvent spills, or fumes are factors |
| Material Description | Heavy-gauge polyvinylchloride in roll form |
| Maximum Leachable Chlorides, see SES N01-F10 | Below 40,000 ppm |
| Moisture Resistance or Water | 0.05 perms max |
| Vapor Permeability | |
| Compressive Strength | – |
| Resistance to Handling Breakage | Good |
| Dimensions | Width: 351/2 in or 48 in
Length: Roll of 68 ft or 100 ft Width and length may vary by vendor Thickness: 0.030 in nominal |
| Flame-Spread/Smoke-Density Rating, See ASTM E 84 | Less than 25/greater than 50. Do not use indoors without sprinkler protection or a fireproof finish. |
| Note | Jacketing can be secured with vinyl tape, nylon tacks, bands, or adhesives. Accessories are available from the jacketing distributors. Jacketing should be limited to 20 in OD applications. To provide proper closure of the jacketing seams upon application, material should be ordered from the vendor precurled or precurling will be required in the field. Can be used indoors and outdoors. Unaffected by ultraviolet rays. PVC will soften above
71 C (160 F). An unsealed slide joint is recommended every 25 ft for thermal expansion of the pipe and jacketing. Provide an unsealed slide joint between fittings when the distance exceeds 8 ft. Check chemical exposure before specifying. See SES N01-F10 for metal substrate protection required. |
| Approved Materials and Vendors | CEEL-Tite 330
CEEL-Co. Dura-Jac SX 0.030 in Sproule Mfg. Co. |
| LoSmoke 30 mil
Proto-Jac Proto Corp. |
|
| P.I.C. FG30
P.I.C. Plastics, Inc. Zeston 2000 30 mil Manville Mechanical Insulation Div. Schuller International, Inc. |
CODE 748.4 (Ribbed panels)
| Material Designation | Ribbed panels |
| Recommended Temperature
Range |
-18 to +66 C max (0 to +150 F max) |
| Purpose | Finish for thermal insulation on vertical vessels. Preferred finish where durability, weather or chemical resistance, cleanliness, appearance, oil or solvent spills, or fumes are factors. |
| Material Description | Heavy-gauge polyvinylchloride in panel form |
| Maximum Leachable Chlorides, see
SES N01-F10 |
Below 40,000 ppm |
| Moisture Resistance or Water
Vapor Permeability |
0.05 perms max |
| Resistance to Handling Breakage | Good |
| Dimensions | Thickness: 0.040 in minimum
Panel dimensions upon request from vendor |
| Flame-Spread/Smoke-Density
Rating, See ASTM E 84 |
Less than 25/greater than 50. Do not use indoors without sprinkler protection or a fireproof finish. |
| Note | The panels shall be secured with adhesives and bands. Accessories are available from the jacketing distributors. Unaffected by ultraviolet rays. PVC will soften above 71 C (160 F). Check chemical exposure before specifying. Can be used indoors and outdoors. See SES N01-F10 for metal substrate protection required. Additional banding is required for
large-diameter tanks and vessels. |
| Approved Materials and Vendors | Ceel-Co Ribbed Panels
CEEL-Co. |
CODE 749 (RTP (FRP) jacket)
| Material Designation | RTP (FRP) jacket |
| Recommended Temperature Range | -7 to +149 C max (+20 to +300 F max) |
| Purpose | Corrosion-resistant finish for pipe and equipment with minimum insulation outside diameter of 16 in |
| Material Description | Glass fiber reinforced thermoset plastic resin (RTP) |
| Maximum Leachable Chlorides, see SES N01-F10 | Below 100 ppm |
| Moisture Resistance or Water Vapor Permeability | Good |
| Resistance to Handling Breakage | Good |
| Dimensions | Thickness: 0.030 in nominal Standard width of 48 in 100 ft rolls Other size combinations are available |
| Flame-Spread/Smoke-Density Rating, See ASTM E 84 | Less than 25/greater than 50. Do not use indoors without sprinkler protection or a fireproof finish. |
| Note | Resistant to most acids, bases, and solvents. Check exposure before specifying. Specify that the jacket shall be fabricated with fire- and corrosion-resistant materials. See SES N01-F10 for metal substrate protection required. |
| Approved Materials and Vendors | FRP Jacketing
Pamrod Products Co. Dura-Jac ‘H.D.’ Sproule Manufacturing Co. |
CODE 749.1 (RTP (FRP) fitting covers)
| Material Designation | RTP (FRP) fitting covers |
| Recommended Temperature
Range |
-7 to +149 C max (+20 to +300 F max) |
| Purpose | Corrosion-resistant preformed covers for large diameter fittings as an alternate to gore-type metal covers |
| Material Description | Glass-fiber-reinforced thermoset plastic resin (RTP) |
| Maximum Leachable Chlorides, see
SES N01-F10 |
Below 100 ppm |
| Moisture Resistance or Water
Vapor Permeability |
Good |
| Resistance to Handling Breakage | Good |
| Flame-Spread/Smoke-Density
Rating, See ASTM E 84 |
Less than 25/greater than 50. Do not use indoors without sprinkler protection or a fireproof finish. |
| Note | Resistant to most acids, bases, and solvents. Check exposure before specifying. See SES N01-F10 for metal substrate protection required. Standard colors are aluminum-gray or white. |
| Approved Materials and Vendors | Dur-Jac ‘H.D.’ Flange, Tee, End Cap, 45 and 90 Ell Covers
Sproule Mfg. Co. |
| FRP Flange, Tee, End Cap, 45 and 90 Ell Covers
Pamrod Products Co. |
CODE 750(a) (Metal mesh knitted)
| Material Designation | Metal mesh knitted |
| Recommended Temperature | +649 C max (+1200 F max) |
| Range | |
| Purpose | Abuse-resistant covering for removable-reusable insulation pads – indoors or outdoors. It is also recommended for some insulation pads exposed to temperatures above +650 F. |
| Material Description | A stainless steel wire, knitted into a tubular fabric using a mesh size of 60 density |
| Resistance to Handling Breakage | Excellent |
| Dimensions | Wire Thickness: 0.011 in
Width: 30 in tubular (60 in open width) Length: 132 ft |
| Note | Type 304 stainless steel wire fabric for protecting the outlet surface of removable-reusable insulation pads from severe mechanical abuse or high temperatures. The wire fabric may encapsulate the pad or be limited to the surfaces requiring the protection. The wire fabric is normally secured to the insulation pad with stainless steel hog rings. Some chemicals and chlorides will attack stainless steel. Check exposure before specifying. |
| Approved Materials and Vendors | Alpha-Maritex 91160(a)
Alpha Associated, Inc. Part No. 55-2350-4480-01 Metal Mesh Metex Corp.(a) |
Note:
(a) Available crimped for added strength.
CODE 751 (32 mil smooth aluminum jacket)
| Material Designation | 32 mil smooth aluminum jacket |
| Purpose | Finish for thermal insulation where abuse resistance, weather resistance, cleanliness, appearance, oil or solvent spills or fumes, and flame-spread resistance are factors |
| Material Description | Smooth aluminum in roll form with a protective backing on inner surface |
| Moisture Resistance or Water
Vapor Permeability |
Impermeable |
| Resistance to Handling Breakage | Good |
| Dimensions | Width: 36 in or 48 in
Length: Rolls of 100 ft Thickness of aluminum: 0.032 in nominal |
| Note | Attacked by most acids, chlorides, and some hydroxides. Check exposure before specifying. The protective backing shall be a minimum of 2.5 mil total thickness coextruded polyethylene and DuPont Surlyn continuously
heat-sealed to the metal. The Surlyn shall be a minimum of 1 mil. The protective backing must qualify per SN219P. Aluminum sheeting conforms to ASTM B 209. |
| Approved Materials and Vendors | 32 Mil Aluminum Jacket with 2.5 Mil Poly/Surlyn
Childers Products Co. |
| 0.032 in Sure-Fit Roll Jacketing with 2.5 Mil Poly/Surlyn
Pabco Division of Fibreboard Corp. |
|
| 32 Mil Aluminum Jacket with 2.5 Mil Poly/Surlyn
RPR Products, Inc. |
CODE 751.1 (32 mil smooth aluminum jacket, acrylic-coated)
| Material Designation | 32 mil smooth aluminum jacket, acrylic-coated |
| Purpose | Finish for thermal insulation where abuse resistance, weather or chemical resistance, cleanliness, appearance, oil or solvent spills or fumes, and flame-spread resistance are factors |
| Material Description | Smooth aluminum in roll form with a white acrylic coating on exterior and a protective backing on inner surface |
| Moisture Resistance or Water
Vapor Permeability |
Impermeable |
| Resistance to Handling Breakage | Good |
| Dimensions | Width: 36 in or 48 in
Length: Rolls of 100 ft Thickness of aluminum: 0.032 in nominal |
| Note | Exterior surface to have a white acrylic coating nominal 0.8 mil dry-film thickness. Some acids will attack coating. Check exposure before specifying. The protective backing shall be a minimum of 2.5 mil total thickness coextruded polyethylene and DuPont Surlyn continuously heat-sealed to the metal. The Surlyn shall be a minimum of 1 mil. The
protective backing must qualify per SN219P. Aluminum sheeting conforms to ASTM B 209. |
| Approved Materials and Vendors | 32 Mil Aluminum Jacket with 2.5 Mil Poly/Surlyn
Childers Products Co. |
| Acrylic Coated Aluminum Jacket, 32 Mil Thick with 2.5 Mil Poly/Surlyn
RPR Products, Inc. |
|
| 0.032 in Sure-Fit Roll Jacketing, Acrylic-Coated with 2.5 Mil Poly/Surlyn
Pabco Division of Fibreboard Corp. |
CODE 752 (24 mil smooth aluminum jacket)
| Material Designation | 24 mil smooth aluminum jacket |
| Purpose | Finish for thermal insulation where abuse resistance, weather resistance, cleanliness, appearance, oil or solvent spills or fumes, and flame-spread resistance are factors |
| Material Description | Smooth aluminum in roll form with a protective backing on inner surface |
| Moisture Resistance or Water
Vapor Permeability |
Impermeable |
| Resistance to Handling Breakage | Good |
| Dimensions | Width: 36 in or 48 in
Length: Rolls of 100 ft Thickness of aluminum: 0.024 in nominal |
| Note | Attacked by most acids, chlorides, and some hydroxides. Check exposure before specifying. The protective backing shall be a minimum of 2.5 mil total thickness coextruded polyethylene and DuPont Surlyn continuously
heat-sealed to the metal. The Surlyn shall be a minimum of 1 mil. The protective backing must qualify per SN219P. Aluminum sheeting conforms to ASTM B 209. |
| Approved Materials and Vendors | 24 Mil Aluminum Jacket with 2.5 Mil Poly/Surlyn
Childers Products Co. |
| 0.024 in Sure-Fit Roll Jacket with 2.5 Mil Poly/Surlyn
Pabco Division of Fibreboard Corp. |
|
| 24 Mil Aluminum Jacket with 2.5 Mil Poly/Surlyn
RPR Products, Inc. |
CODE 752.1 (24 mil smooth aluminum jacket, acrylic-coated)
| Material Designation | 24 mil smooth aluminum jacket, acrylic-coated |
| Purpose | Finish for thermal insulation where abuse resistance, weather or chemical resistance, cleanliness, appearance, oil or solvent spills or fumes, and flame-spread resistance are factors |
| Material Description | Smooth aluminum in roll form with a white acrylic coating on exterior and a protective backing on inner surface |
| Moisture Resistance or Water
Vapor Permeability |
Impermeable |
| Resistance to Handling Breakage | Good |
| Dimensions | Width: 36 in or 48 in
Length: Rolls of 100 ft Thickness of aluminum: 0.024 in nominal |
| Note | Exterior surface to have a white acrylic coating nominal 0.8 mil dry-film thickness. Some acids will attack coating. Check exposure before specifying. The protective backing shall be a minimum of 2.5 mil total thickness coextruded polyethylene and DuPont Surlyn continuously heat-sealed to the metal. The Surlyn shall be a minimum of 1 mil. The
protective backing must qualify per SN219P. Aluminum sheeting conforms to ASTM B 209. |
| Approved Materials and Vendors | 24 Mil Aluminum Jacket, Acrylic Finish with 2.5 Mil Poly/Surlyn
Childers Products Co. |
| Acrylic Aluminum Jacket, 24 Mil thick with 2.5 Mil Poly/Surlyn
RPR Products, Inc. |
|
| 0.024 in Sure-Fit Roll Jacketing, Acrylic-Coated with 2.5 Mil Poly/Surlyn
Pabco Division of Fibreboard Corp. |
CODE 752.2 (24 mil deep-corrugated aluminum jacket)
| Material Designation | 24 mil deep-corrugated aluminum jacket |
| Purpose | Finish for thermal insulation on vertical vessels. Preferred finish where rigidity, abuse resistance, weather resistance, cleanliness, appearance, oil or solvent spills or fumes, and flame-spread resistance are factors. |
| Material Description | Aluminum sheets with 11/4 in corrugations and a protective backing on the interior surface. A more rigid material than Code 716. Finish: smooth or cross-crimped as specified on order. |
| Moisture Resistance or Water
Vapor Permeability |
Impermeable |
| Resistance to Handling Breakage | Good |
| Dimensions | Width: 33 in or 44 in (36 in available at added costs) Length: 6 ft through 12 ft
Thickness: 0.024 in nominal |
| Note | Attacked by most acids, chlorides, and some hydroxides. Check exposure before specifying. The protective backing shall be 40 lb/3000 ft2 kraft paper and 3 mil polyethylene extrusion laminate heat-sealed to the aluminum sheet over the entire interface area or a minimum of 2.5 mil total thickness coextruded polyethylene and DuPont Surlyn continuously heat-sealed to the metal. The Surlyn shall be a minimum of 1 mil. The poly/kraft protective backing shall be identified on the product to indicate 3 mil polyethylene. The protective backing must qualify per SN219P. Aluminum sheeting conforms to ASTM B 209. |
| Approved Materials and Vendors | 24 Mil Deep-Corrugated Aluminum Jacketing with 3 Mil Poly/Kraft or 2.5 Mil
Poly/Surlyn(a) Childers Products Co. |
| 0.024 in Sure-Fit Deep-Corrugated Sheets – Aluminum with 3 Mil Poly/Kraft or 2.5 Mil Poly/Surlyn
Pabco Division of Fibreboard Corp. |
|
| 24 Mil Deep-Corrugated Aluminum with 2.5 Mil Poly/Surlyn
RPR Products, Inc. |
Note:(a)State complete specification and required length on order.
CODE 752.3 (24 mil deep-corrugated aluminum jacket acrylic-coated)
| Material Designation | 24 mil deep-corrugated aluminum jacket acrylic-coated |
| Purpose | Finish for thermal insulation on vertical vessels. Preferred finish where rigidity, abuse resistance, weather resistance, cleanliness, appearance, oil or solvent spills or fumes, and flame-spread resistance are factors. |
| Material Description | Aluminum sheets with 11/4 in corrugations and a white acrylic coating on the exterior and a protective backing on the interior surface. A more rigid material than Code 716.5. |
| Moisture Resistance or Water
Vapor Permeability |
Impermeable |
| Resistance to Handling Breakage | Good |
| Dimensions | Width: 33 in through 44 in (36 in available at added costs) Length: 6 ft through 12 ft
Thickness: 0.024 in nominal |
| Note | Exterior surface to have a white acrylic coating nominal 0.8 mil dry-film thickness. Some acids will attack coating. Check exposure before specifying. The protective backing shall be 40 lb/3000 ft2 kraft paper and
3 mil polyethylene extrusion laminate heat-sealed to the aluminum sheet over the entire interface area or a minimum of 2.5 mil total thickness coextruded polyethylene and DuPont Surlyn continuously heat-sealed to the metal. The Surlyn shall be a minimum of 1 mil. The poly/kraft protective backing shall be identified on the product to indicate 3 mil polyethylene. The protective backing must qualify per SN219P. Aluminum sheeting conforms to ASTM B 209. |
| Approved Materials and Vendors | 24 Mil Deep-Corrugated Aluminum Jacket, Acrylic Finish with 3 Mil
Poly/Kraft or 2.5 Mil Poly/Surlyn Childers Products Co. |
| 0.024 in Sure-Fit Deep-Corrugated Sheets – Aluminum, Acrylic-Coated with
3 Mil Poly/Kraft or 2.5 Mil Poly/Surlyn Pabco Division of Fibreboard Corp. |
|
| 24 Mil Deep-Corrugated Aluminum with 3 Mil Poly/Kraft or 2.5 Mil
Poly/Surlyn Acrylic-Coated RPR Products, Inc. |
Note:
(a) State complete specification and required length on order.
CODE 752.4 (32 mil deep-corrugated aluminum jacket, Tedlar-coated)
| Material Designation | 32 mil deep-corrugated aluminum jacket, Tedlar-coated |
| Purpose | Finish for thermal insulation on vertical vessels. A preferred finish where abuse resistance, specific chemical resistance, cleanliness, appearance, oil or solvent spills or fumes, and flame-spread resistance are factors. |
| Material Description | Aluminum sheets with 11/4 in corrugations and a white Tedlar PVF film laminated to the exterior and a protective backing on the interior surface. A more rigid material than Code 752.5. |
| Moisture Resistance or Water
Vapor Permeability |
Impermeable |
| Resistance to Handling Breakage | Good |
| Dimensions | Width: 33 in
Length: Up to 12 ft Thickness of aluminum: 0.032 in nominal Thickness of Tedlar PVF film: 1.5 mil |
| Note | White Tedlar PVF film 1.5 mil thick laminated to the exterior surface. Resistant to most acids, bases, and solvents. Check exposure before specifying. The protective backing shall be 40 lb/3000 ft2 kraft paper and
3 mil polyethylene extrusion laminate heat-sealed to the aluminum sheet over the entire interface area or a minimum of 2.5 mil total thickness coextruded polyethylene and DuPont Surlyn continuously heat-sealed to the metal. The Surlyn shall be a minimum of 1 mil. The poly/kraft protective backing shall be identified on the product to indicate 3 mil polyethylene. The protective backing must qualify per SN219P. Aluminum sheeting conforms to ASTM B 209. |
| Approved Materials and Vendors | 32 Mil Deep-Corrugated Aluminum Jacket, Ultrolon Finish with 3 Mil
Poly/Kraft or 2.5 Mil Poly/Surlyn Childers Products Co. |
| 32 Mil Deep-Corrugated Aluminum Jacket Tedlar Finish with 3 Mil Poly/Kraft or 2.5 Mil Poly/Surlyn
RPR Products Inc. |
CODE 752.5 (32 mil smooth aluminum jacket, Tedlar-coated)
| Material Designation | 32 mil smooth aluminum jacket, Tedlar-coated |
| Purpose | Finish for thermal insulation where abuse resistance, specific chemical resistance or weather, cleanliness, appearance, oil or solvent spills or fumes, and flame-spread resistance are factors |
| Material Description | Smooth aluminum in roll form with a white Tedlar PVF film laminated to the exterior and a protective backing on the inner surface |
| Moisture Resistance or Water
Vapor Permeability |
Impermeable |
| Resistance to Handling Breakage | Good |
| Dimensions | Width: 36 in
Length: Roll of 100 ft Thickness of aluminum: 0.032 in nominal Thickness of Tedlar PVF film: 1.5 mil |
| Note | White Tedlar PVF film 1.5 mil thick laminated to the exterior surface. Resistant to most acids, bases, and solvents. Check exposure before specifying. The protective backing shall be a minimum of 2.5 mil total thickness coextruded polyethylene and DuPont Surlyn continuously heat-sealed to the metal. The Surlyn shall be a minimum of 1 mil. The
protective backing must qualify per SN219P. Aluminum sheeting conforms to ASTM B 209. |
| Approved Materials and Vendors | 32 Mil Aluminum Jacket, Ultrolon Finish with 2.5 Mil Poly/Surlyn
Childers Products Co. |
| 32 Mil Aluminum Jacket, Tedlar coated with 2.5 Mil Poly/Surlyn
RPR Products Inc. |
CODE 753 (10 mil smooth stainless steel jacket)
| Material Designation | 10 mil smooth stainless steel jacket |
| Purpose | Finish for thermal insulation where chemical resistance or fire protection (or both) are factors |
| Material Description | Smooth stainless steel in roll form with a protective backing on the inner surface |
| Moisture Resistance or Water
Vapor Permeability |
Impermeable |
| Resistance to Handling Breakage | Excellent |
| Dimensions | Width: 36 in
Length: Roll of 50 ft min Thickness: 0.010 in min |
| Note | Type 300 series stainless steel with a 2B mil finish. Low emissivity of bare stainless steel results in surface temperatures up to +40 F greater than other finishes such as mastic or coated metals. For installation, use bands only as indicated in SN215P. Minimum protective backing to be either nominal 40 lb/3000 ft2 kraft paper and 3 mil polyethylene extrusion laminate heat-sealed to the metal over the entire inner surface area or a minimum of
2.5 mil total thickness coextruded polyethylene and DuPont Surlyn continuously heat-sealed to the metal. The Surlyn shall be a minimum of 1 mil. The poly/kraft protective backing shall be identified on the product to indicate 3 mil polyethylene. The protective backing must qualify per SN219P. Stainless steel sheeting conforms to ASTM A 167 and A 240. |
| Approved Materials and Vendors | 10 Mil Stainless Steel Jacketing/with 3 Mil Poly/Kraft or 2.5 Mil Poly/Surlyn
Barrier Childers Products Co. |
| 10 Mil Stainless Steel Jacketing/with 3 Mil Poly/Kraft or 2.5 Mil Poly/Surlyn
Barrier RPR Products, Inc. |
|
| 0.010 in Sure-Fit Stainless Steel Roll Jacketing, 3 Mil Poly-Weld or 2.5 Mil
Poly/Surlyn Barrier Pabco Division of Fibreboard Corp. |
CODE 753.1 (10 mil stainless steel fitting covers)
| Material Designation | 10 mil stainless steel fitting covers |
| Purpose | Finish for thermal insulation on pipe fittings where chemical resistance or fire protection (or both) are factors |
| Material Description | Sheet stainless steel cold-formed or rolled into covers. Fits combination of pipe size and insulation thickness |
| Moisture Resistance or Water
Vapor Permeability |
Impermeable |
| Resistance to Handling Breakage | Excellent |
| Dimensions | Sizes: See manufacturer literature
Thickness: 0.010 in min |
| Note | Type 300 series stainless steel with a 2B mil finish |
| Approved Materials and Vendors | Stainless Steel 90 Univers-Ell Jac, Tee-Jac and End Cap-Jac
Childers Products Co. |
| Stainless Steel 90 Ell, Tee and End Cap
RPR Products, Inc. |
|
| Sure-Fit Stainless Steel 45 and 90 Ells
Pabco Div. of Fibreboard Corp. |
CODE 753.4 (10 mil deep-corrugated stainless steel jacket)
| Material Designation | 10 mil deep-corrugated stainless steel jacket |
| Purpose | Finish for thermal insulation on vertical vessels where chemical resistance or fire protection (or both) are factors |
| Material Description | Stainless steel sheets with 11/4 in corrugations with a protective backing on the inner surface. A more rigid material than Code 753. |
| Moisture Resistance or Water
Vapor Permeability |
Impermeable |
| Resistance to Handling Breakage | Excellent |
| Dimensions | Width: 33 in
Length: Up to 10 ft Thickness of stainless steel: 0.010 in min |
| Note | Type 300 series stainless steel with a 2B mil finish. Low emissivity of bare stainless steel results in surface temperatures up to +40 F greater than other finishes such as mastic or coated metals. For installation, use bands only as indicated in SN215P. Minimum protective backing to be either nominal 40 lb/3000 ft2 kraft paper and 3 mil polyethylene extrusion laminate heat-sealed to the metal over the entire inner surface area or a minimum of
2.5 mil total thickness coextruded polyethylene and DuPont Surlyn continuously heat-sealed to the metal. The Surlyn shall be a minimum of 1 mil. The poly/kraft protective backing shall be identified on the product to indicate 3 mil polyethylene. The protective backing must qualify per SN219P. Stainless steel sheeting conforms to ASTM A 167 and A 240. |
| Approved Materials and Vendors | 10 Mil Deep-Corrugated Stainless Steel Jacketing with 3 Mil Poly/Kraft or
2.5 Mil Poly/Surlyn Barrier Childers Products Co. |
| 10 Mil Deep-Corrugated Stainless Steel Jacketing with 3 Mil Poly/Kraft or
2.5 Mil Poly/Surlyn Barrier RPR Products, Inc. |
|
| 0.010 Deep-Corrugated Sure-Fit Stainless Steel Roll Jacketing, 3 Mil
Poly-Weld or 2.5 Mil Poly/Surlyn Barrier Pabco Division of Fibreboard Corp. |